Ventis - VB00020 - Ventis HES350 Wood Stove
Description
Ventis HES350 Wood Stove on pedestal is designed to accommodate a large spaces. It has a 3.5 ft³ firebox, which is one of the largest fireboxes for a freestanding wood stove. This unit features non-catalytic combustion technology and will heat up to 2,700 sq. ft. It can handle up to a 22-Inch log and produces up to 110,000 BTUs. It will keep you warm in the winter months with a maximum burn time of 10 hours.
Features
-
Extra-large wood stove on pedestal
-
EPA certified at only 1.32 g/h
-
Solidity and manufacturing quality
- C-Cast heat shield added to the firestop
-
Non-catalytic combustion technology
-
Installation authorized on the Island of Montreal
-
Cast iron door
- Top heat deflector and side panels
Appliance Performance
| Fuel type |
Dry cordwood (16" recommended) |
| Recommended heating area |
1,000 - 2,700 ft² |
| Overall firebox volume |
3.5 ft³ |
| EPA loading volume |
2.84 ft³ |
| Maximum burn time |
10 hours |
| Maximum heat output-dry cordwood |
110,000 BTU/h |
| Minimum overall heat output rate |
18,100 BTU/h (5.3 kW) |
| Maximum overall heat output rate |
49,500 BTU/h (14.5 kW) |
| Average efficiency-dry cordwood (HHV) |
71 % |
| Average efficiency-dry cordwood (LHV) |
76 % |
| Optimum efficiency |
77 % |
| Optimum heat transfer efficiency |
76 % |
| Average particulate emission rate |
1.32 g/h |
| Average CO |
92 g/h |
- Performances based on a fuel load prescribed by the standard at 7 lb/ft³ and with a moisture content between 19% and 25%.
- Optimum overall efficiency at a specific burn rate (LHV).
- This appliance is officially tested and certified by an independent agency.
- The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb/ft³ and 20 lb/ft³. Other performances are based on a fuel load prescribed by the standard. The specified loading density varies between 7 lb/ft³ and 12 lb/ft³. The moisture content is between 19% and 25%.
- As measured per CSA B415.1-10 stack loss method.
- Higher Heating Value of the fuel.
- Lower Heating Value of the fuel.
- The optimum heat transfer efficiency is for the low burn rate (using HHV) and represents the appliance’s ability to convert the energy contained in the solid fuels into energy transferred to the room in the form of heat and does not take into account the chemical losses during combustion.
- Recommended heating area and maximum burn time may vary subject to location in home, chimney draft,heat loss factors, climate, fuel type and other variables. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure.
- Carbon monoxyde.
General Features
| Maximum log length |
22" |
| Overall dimension (Width) |
28 3/4" |
| Overall dimension (Height) |
34 3/4" |
| Overall dimension (Depth) |
30 5/8" |
| Alcove installation approved |
Yes |
| Mobile home approved |
Yes, with fresh air intake |
| Premium quality blower included (CFM) |
Optional |
| Certified according to applicable standards |
CAN/USA accredited laboratory |
| Combustion technology |
Non-catalytic |
| Stainless-steel secondary-air system |
Yes |
| Flue outlet diameter |
6" |
| Recommended chimney diameter |
6" |
| Type of chimney |
CAN/ULC S629, UL 103 HT (2100 °F) |
| Minimum chimney height |
12' |
| Door type |
Single, glass with cast iron frame |
| Door opening size (Width) |
19" |
| Door opening size (Height) |
9 1/4" |
| Glass type |
Ceramic glass |
| Glass surface - W x H |
18 3/8" x 11 1/2" |
| Firebox size (Width) |
22 7/8" |
| Firebox size (Height) |
12 3/4" |
| Firebox size (Depth) |
20 1/8" |
| Log positioning |
Loading over width and over depth |
| Firebox lined with refractory bricks |
Yes |
| Baffle type |
High quality vermiculite |
| High-efficiency certified appliance |
Yes, EPA 2020 certified |
| Canadian Standard (emissions) |
CSA B415.1-10 |
| USA Standard (emissions) |
EPA |
| Canadian Standard (safety) |
ULC S627 |
| USA Standard (safety) |
UL 1482, UL 737 |
| Steel thickness-body |
3/16" |
| Steel thickness-top |
5/16" |
